m83401, C83401 www.vishay.com vishay dale thin film revision: 01-mar-13 61 document number: 60116 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 thin film resistor network m ilitary, mil-prf-83401 qualified, type rz070, rz080, rz090, rz210, rz220, rz230, single-in-line sip qualified to meet mil-prf-83401 ch aracteristic r, v, and h these resistor networks are available in 6 pins, 8 pins, and 10 pins in schematic c and g st yles. custom circuits are not available. schematic c and g only. they incorporate vishay dale thin films patented pa ssivated nichrome film to give superior performance on temperature coefficient of resistance, thermal stability, noise, voltage coefficient, power handling and resistance stability. the leads are attached to the metallized alumina substrates by thermo-compression bonding. the body is molded thermoset plastic with gold pl ated copper alloy leads. this product will outperform all of the requirements of characteristic r, v, and h of mil-prf-83401. features ? mil-prf-83401 qualified (cage code 57489) ? low profile 0.195" (4.95 mm seated height) ? characteristics r ( 25 ppm), h, v, k, and m ? hot fused tin/lead 60/40 solder dipped ? rugged molded low profile construction with standoff ? 100 % screened to groups a mil-prf-83410 testing ? tolerances to 0.1 % ? isolated and bussed (schematic c and g) typical performance schematic notes (1) consult mil-prf-83401 (2) h characteristic 100 ? to 100 k ? resistance range at 0.1% best r characteristic 250 ? to 100 k ? resistance range at 0.1% best r characteristic 250 ? to 200 k ? resistance range at 1% best absolute tracking tcr 25 5 absolute ratio tol. 0.1 0.1 to 0.05 standard electrical specifications test specifications conditions material passivated nichrome - pin/lead number 6, 8, 10 - resistance range 100 ? to 200 k ? per resistor tole rance dependent (2) tcr: absolute 25 ppm/c to 300 ppm/c - 55 c to + 125 c (1) tcr: tracking 5 ppm/c - 55 c to + 125 c tolerance: absolute 0.1 % to 5.0 % + 25 c tolerance: ratio 0.1 % to r 1 + 25 c power rating: resistor 0.06 mw to 0.120 mw (per element typical at + 25 c) (1) maximum at + 70 c power rating: package 0.18 w to 1.08 w (1) maximum at + 70 c stability: absolute ? r 0.05 % 2000 h at + 70 c stability: ratio ? r 0.015 % 2000 h at + 70 c voltage coefficient < 0.1 ppm/v - working voltage 100 v - operating temperature range - 55 c to + 125 c - storage temperature range - 55 c to + 125 c - noise < - 30 db - thermal emf < 0.08 v/c - shelf life stability: absolute ? r 0.01 % 1 year at + 25 c shelf life stability: ratio ? r 0.002 % 1 year at + 25 c 1 c schematic (pin 1 common) 234 n 1 g schematic (isolated) 23 4 n
m83401, C83401 www.vishay.com vishay dale thin film revision: 01-mar-13 62 document number: 60116 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 power derating dimensions and imprinting in inches and millimeters dimension inches millimeters a 0.035 0.89 b 0.040 1.02 c 0.100 0.005 non-accum. 2.54 0.13 d 0.019 0.006 typical 0.48 0.15 e 0.187 0.010 4.75 0.25 f 0.135 3.43 g 0.095 2.41 h 0.012 0.004 0.31 0.10 l (6 pins) 0.583 - 0.023/+ 0.01 14.81 - 0.584/+ 0.254 l (8 pins) 0.783 - 0.023/+ 0.01 19.89 - 0.584/+ 0.254 l (10 pins) 0.983 - 0.023/+ 0.01 24.97 - 0.584/+ 0.254 construction mechanical specifications resistive element tamelox passivated nichrome substrate material alumina body molded epoxy terminals copper alloy plating/solder nickel/gold/sn63 fussed c schematic (pin 1 common characteristic h) g schematic (isolate d characteristic h) l a indicates pin 1 b cd e f g h vishay logo part number date code high purity alumina substrate gold plated copper leads gold to gold thermo-compression bond (no internal solder) sputtered film system low profile 1.08 0.12 10 pin package 8 pin package 6 pin package single resistor - 55 + 25 + 70 + 125 + 150 0.60 0.84 power rating (w) ambient temperature c 0.06 single resistor (char. r and v) 0 0.54 10 pin package (char. r and v) 0.60 0.48 0.36 0.12 10 pin package 8 pin package 6 pin package single resistor low profile - 55 0 + 25 + 70 + 125 + 150 power rating (w) ambient temperature c 0.06 0.30 10 pin package (char. r and v) single resistor (char. r and v)
m83401, C83401 www.vishay.com vishay dale thin film revision: 01-mar-13 63 document number: 60116 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes (1) no internal solder (2) v" is not required for characteristics r, h, and v, it is only required for k and m. characteristics tolerance equal to or gre ater than 1 %." (3) h characteristic 100 ? to 100 k ? resistance range at 0.1% best r characteristic 250 ? to 100 k ? resistance range at 0.1% best r characteristic 250 ? to 200 k ? resistance range at 1% best global part number information new global part numb ering: m8340107h1000bcuf model (5 digits) schematic (2 digits) characteristic (1 digits) resistance (4 digits) tolerance (1 digits) schematic (1 digits) packaging (2 digits) vendor (1 digits) m83401 single in-line resistor network low profile C83401 non burn in screened network 07 = 6 pin 08 = 8 pin 09 = 10 pin 21 = 6 pin (1) 22 = 8 pin (1) 23 = 10 pin (1) h = 50 ppm/c v = 50 ppm/c 5 ppm/c track r = 25 ppm/c 5 ppm/c track k = 100 ppm/c m = 300 ppm/c first 3 digits are significant figures and the last digit specifies the number of zeros to follow. (100 ? to 100 k ? ) examples: 1000 = 100 ? ? 1001 = 1000 ? b = 0.1 % (3) d = 0.5 % (3) f = 1 % g = 2 % j = 5 % c = pin 1 common g = isolated resistors uf = tubed ui = 100 min, 1 mult (item single lot date code) up = 100 min.,1 mult (package unit single lot date) v (2) = vishay dale thin film model schematic characteristic resistance range tolerance schematic m83401 C83401 07 = 6 pin (rz070) 08 = 8 pin (rz080) 09 = 10 pin (rz090) 21 = 6 pin (rz210) 22 = 8 pin (rz220) 23 = 10 pin (rz230) h = 50 ppm/c 100 to 100k b, d, f, g, j c, g v = 50 ppm/c/ 5 ppm/c track 250 to 100k b, d, f, g, j 250 to 200k f, g, j r = 25 ppm/c 5 ppm/c track 250 to 100k b, d, f, g, j 250 to 200k f, g, j k = 100 ppm/c 100 to 100k b, d, f, g, j m = 300 ppm/c 0107 100 h m3 bcu 0 fv 8 4
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
